Get 6 Months To Pay On Purchases of $99 or more with
The leader in GX Honda & Chinese OHV Performance
Aftermarket muffler for GX200s, 6.5 OHVs, and 212 Predators
1 1/8" Pipe x 2" Long,Use to adapt 1 1/8" Mufflers to 1" pipe.Recommended that clamp be slotted with hacksaw or band saw if using clamps
Use to Clamp 1 5/16"" RLV mufflers to pipe
Flange for making your own exhaust.Picture for Reference Only
Use to prevent mufflers from falling off. Fits BSP/AKRA Wiener pipe
Use to Clamp RLV mufflers to pipe. Fit all 1" mufflers.
Use to Clamp 1" RLV mufflers. (Will work up to 1 1/8")
Use to Clamp RLV mufflers to pipe. Fit all 1 5/16" mufflers.
3/4" "Sausage can" muffler. Use for QMA/USAC, RTT Chinese OHV, GX200 Mud Pipes and any other pipes using 3/4' screw in
Used for BSP & Wiener Pipe classes requiring 1/2" Briggs Muffler
Exhaust bend for custom applications. 1" OD pipe with one end flared to 1" ID Picture is for reference only. Straight Pipe does NOT have flange. Order flange or stub seperate
Protect your motor when storing and transporting (Color may vary).
Exhaust bend for custom applications. 1 1/8 (1.125) " OD pipe with one end flared to 1 1/8" ID Picture is for reference only. Straight Pipe does NOT have flange. Order flange or stub seperate
Exhaust bend for custom applications. 1 1/4 (1.25) " OD pipe with one end flared to 1 1/4" ID Picture is for reference only. Straight Pipe does NOT have flange. Order flange or stub seperate
Aftermarket muffler for GX390s and 420 OHVs
The High Temperature (HT) Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. DEI recommend the use of this coating with their exhaust wrap because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. HT Silicone Coating is VOC (Volatile Organic Compounds) compliant in all 50 states. Recommended for use with DEI non-Titanium exhaust wraps, HT Silicone Coating penetrates, seals and protects as well as helping to extend the lifespan of exhaust wrap.
Use on RLV 5438 to prevent breakage. Will also work on Mini-bike pipes, but some bending will be needed. Requires two Hose type clamps (not included). May also be welded to pipe.
Flange for making your own exhaustPicture is for reference Only. You will get a header flange with a short piece of pipe welded to it. Uses 1 1/8" Pipe and bends
Flange for making your own exhaustPicture is for reference Only. You will get a header flange with a short piece of pipe welded to it. Uses 1" Pipe and bends
Use on RLV 5435 to prevent breakage. Requires two Hose type clamps (not included). May also be welded to pipe. Picture for reference only (Engine and Pipe not included)
Genuine Honda UT2 muffler shield for GX240s to GX270s
1" screw on muffler used for 390 Mud Boat Pipes
OEM Honda Take off, complete with shield. Gaskets not Included. Fits GX1`20 & GX160s
MINI 91 for BSP classes using the "weiner" pipe.
Genuine Honda
Genuine Honda Take off, complete with shield. Gaskets not Included. Fits GX160s and GX200s
Genuine Honda Take off, complete with shield. Gaskets not Included. Fits GX240s thru GX270s
Wrapping headers and down pipes is an important first step in controlling unwanted underhood radiant heat. Keeping exhaust gases hotter within the exhaust system helps in decreasing exhaust density and increases exhaust flow. This improves exhaust scavenging resulting in cooler air intake temperatures for an improvement in performance and a gain in horsepower. ƒ?›Improves horsepower ƒ?›Withstands 1200F direct/2000F radiant ƒ?›Only exhaust wrap with installation guide lines ƒ?›Added durability and heat retention NOTE: Silicone Coating spray is highly recommended for glass fiber weap to penetrate, seal, protect and prolong the lifespan of exhaust wrap.Wire ties not included - Order Seperate
Genuine Honda UT2 muffler (shield not included) for GX240s to GX270s