Get 6 Months To Pay On Purchases of $99 or more with
The leader in GX Honda & Chinese OHV Performance
Low cost and effective valve notcher for Hemi Head 212 Engines. Works with hand held drill. Instructions included.
12 pt 5/16", 3/8" Drive for ARC Rod BoltsPicture for referenec only. Band or markings may vary
`1/4" 12pt, 1/4" Drive for ARC Rod Bolts
Package of 10 inserts. Tap, Drill bit, and Insert tool (not included.
Package of 5 inserts. Tap, Drill bit, and Insert tool (not included.
For 200 Big Bore Motors
For GX120 to 200 (2.75" max bore)
The best way to remove a flywheel. Just remove the nut, screw knocker on end on crank, smack with a hammer. No puller needed, eliminates cracked flywheels from pullers.Approx 8" long and weighs 1 lb 6 oz(note: knocker must not be fully seated against flywheel, leave at least 2 or 3 turns out)GX120 to 200, 6.5 Chinese OHVs
The best way to remove a flywheel. Just remove the nut, screw knocker on end on crank, smack with a hammer. No puller needed, eliminates cracked flywheels from pullers.Knocker is 8" Long and weighs 1 lb, 6 oz(note: knocker must not be fully seated against flywheel, leave at least 2 or 3 turns out)GX240 to GX390, 13hp Chinese OHVs
Adjustable Push Rod tool for checking for proper pushrod length. GX200s and 212 Predators
Adjustable Push Rod tool for checking for proper pushrod length. GX270s
Adjustable Push Rod tool for checking for proper pushrod length. GX340s & GX390s
Air Powered Porting Tool (die Grinder) for use with our porting cutters and kits.
Features:
Small size, light weight, high speed, low noise. Small air consumption, high concentricity, simple, fast and convenient operation.
Specifications:
Material: metal
Collet size: 1/8”, ¼”
Air consumption: 4CFM
Air pressure: 90PSI
Air inlet: ¼”
Free speed: 23,000rpmMay vary from picture
Used for CC chamber on ASN, WKA, BSP engines. Fits in spark plug hole
Kit contains 4 Carbide Cutters for port shaping.Double cut for smooth finishTypically used for rough porting (they finish with paper rolls)Use with our Air Porting Tool #E4126S or any 1/4" die grinder
Material: Carbide
Shank Diameter: approx. 1/4" (6MM)
Shank Length: approx. 150MM--160MM ( 6 Inch )
Model: Large F/, Small F/ C / D
High efficiency, high-quality finish, long service life,
Includes tools and inserts to repair Valve cover, fan shroud, Intake Manifold, GX120 Side Cover, and other 6mm bolts. Picture for reference Only, actual kit may vary.
Includes tools and inserts to repair Head Bolt threads, GX120 to GX200, Side Cover Bolts on GX160 to GX390s, exhaust, and other 8mm bolts. Picture for reference Only, actual kit may vary.
Use to remove hone marks and cross hatching from rods and pistons. Also great for polishing carb bores.
For GX160 and 200 std bore. This is the best and easiest compressor to use. Once you use this, you will never use a band or adjustable compressor again.
Use to lap rings in making sure they are flat. Also used to reduce thickness
Includes tools and inserts to repair Head Bolt threads on GX270 to GX390. Picture for reference Only, actual kit may vary.
Use for head porting and polishing. Also use for finishing after using carbide cutters.Use with our Air Porting Tool #E4126S or any 1/4" die grinder
Use to file end gap. Much better than a file.Required when installing most Wiseco Ring sets
Designed to check lift at the rocker arms but can also check lift at the cam. No need to remove head. Includes dial indicator, GX160/200 and 6.5 Chinese OHVs and extension